59, Jalan Haji Manan,
86000 Kluang,
Johor, Malaysia.
+607-7724184
+607-7734979
+607-7734979
+607-7722018
Foh Hup Industries Sdn Bhd
59, Jalan Haji Manan,
86000 Kluang,
Johor, Malaysia.
59, Jalan Haji Manan,
86000 Kluang,
Johor, Malaysia.
Adjustable Four Hole Nozzle CPT (Red) 8470CPT
| Previous | 4 / 19 | Next |
- Weedicide Sprayers Spare Parts Manufacturer
- Pesticide Sprayers Accessories
- Pesticide Sprayers Parts Manufacturer
- 药水 Pump 配件 厂商
| Part No. | Description | Part No. | Description | Part No. | Description |
| 8401S | Screw | 8420W | Washer | 8441 CPT | Automatic Release CPT |
| 8401N | Nut | 8421 | Jam Nut | 8441B | Union |
| 8401 | Tank Body | 8422 | Nipple Body | 8442 | Pin |
| 8301 | Tank Body | 8422CPT | Nipple Body CPT | 8443 | Autorelease Lever |
| 8301 | Stand Guard | 8422W | Washer | 8445W | Washer |
| 8405 | Strainer | 8424L | Tube for Nipple | 8446 | Sprayer Lance |
| 8407A | Plastic Cover | 8325 | Air Cylinder | 8447W | Washer |
| 8408 | Hook | 8425 | Air Cylinder | 8448A-1 | Cap |
| 8411 | Shoulder Strap | 8428 | Pull bar | 8448A-2 | Nipple |
| 8411CPT | Shoulder Strap CPT | 8429A | Pin | 8448A CPT | Adjustable Cone Nozzle |
| 8412P | TRI-Gride SRG-32 | 8430 | Nut | 8448A-R | O Ring |
| 8413 | Pump Handle CPT | 8431 | Brass Washer | 8453 | Union |
| 8414 | Milled Nut | 8432 | Piston | 8454 | Nipple |
| 8415 | Pump Cylinder | 8433 | Piston ROD | 8455 | PVC Hose |
| 8415SH | Holder | 8433VC | Brass Washer | 8455CPT | PVC Hose CPT |
| 8415W | Washer | 8435 | Plug | 8455CR | Clip |
| 8417 | Ball Bearing | 8436W | Washer | 8458W | Washer |
| 8418 | Valve Body | 8437S | Spring | 8458F | Filter |
| 8418CPT | Valve Body CPT | 8440 | Spindle | 8459 | Cleaning Chamber |
| 8418W | Washer | 8440R | O Ring | 8470CPT | Four Hole Nozzle CPT |
| 8418B | Screw | 8441 | Autorelease Body |
Operating Instruction pfr Use
Screw the Spraying Lance (No. 8446) into the automatic Release (No. 8441) and fix the Adjustable Nozzle (8488A-1) into the Sprayer Lance. Then fix the Pump Handle (No. 8413) to the pump shaft (either on right or left.) The sprayer is now ready for use by moving the Pump Handle upwards and downwards.
Oil all moving parts regularly before use, including the inside of the Pump Cylinder (No. 8415) where the Piston (No. 8432) is situated with No. 30 cylinder oil (GREASE must not be used). Check and clean Ventilation holes on cover (No. 8408) These holes must not be blocked while the sprayer is in use.
Pump some strokes with closed Automatic Release in order to bring the sprayer under pressure and thus spraying can be obtained by pressingthe Lever (No. 8443) downwards. The Automatic Release will shuts automatically by just releasing the lever.
Operating Difficulties
- Remove and clean Nozzles and Vortex which may be obstructed.
- Unscrew the Air Cylinder and clean the Ball Bearing inside the Valve Body.
- Make sure that all the Washers are tightly screwed to prevent leakage.
Precautions
Chemicals containing Corrosive Acids or highly Concentrated Mercury Compound should not be used